Help is available by moving the cursor above any 
symbol or by checking MAQAO website.
[ 4 / 4 ] Application profile is long enough (534.01 s)
To have good quality measurements, it is advised that the application profiling time is greater than 10 seconds.
[ 3 / 3 ] Most of time spent in analyzed modules comes from functions with source/debug info
-g option gives access to debugging informations, such are source locations.
[ 0 / 3 ] Architecture specific options are unknown for some functions (compilation options info are not available)
Architecture specific options are needed to produce efficient code for a specific processor ( -march=(target) ).
Architecture specific options are needed to produce efficient code for a specific processor ( -x(target), -ax(target) or -march=(target)).
[ 0 / 3 ] Most of time spent in analyzed modules comes from functions without compilation options informations
Functions without compilation options information cumulate 8.63% of the time spent in analyzed modules. For libdmumps.so, check that both -g and -grecord-gcc-switches are present. For libmumps_common.so, check that both -g and -grecord-gcc-switches are present. Remark: if such options are indeed used, this can also be due to some compiler built-in functions (typically math) or statically linked libraries. This warning can be ignored in that case.
[ 0 / 3 ] Optimization level is unknown for some functions (compilation options info are not available)
To have better performances, it is advised to help the compiler by using a proper optimization level (-O2 of higher). Warning, depending on compilers, faster optimization levels can decrease numeric accuracy.
[ 3 / 3 ] Host configuration allows retrieval of all necessary metrics.
[ 2 / 2 ] Application is correctly profiled ("Others" category represents 0.00 % of the execution time)
To have a representative profiling, it is advised that the category "Others" represents less than 20% of the execution time in order to analyze as much as possible of the user code
[ 1 / 1 ] Lstopo present. The Topology lstopo report will be generated.
[ 0 / 4 ] Too little time of the experiment time spent in analyzed loops (8.56%)
If the time spent in analyzed loops is less than 30%, standard loop optimizations will have a limited impact on application performances.
[ 2 / 4 ] A significant amount of threads are idle (41.78%)
On average, more than 10% of observed threads are idle. Such threads are probably IO/sync waiting. Some hints: use faster filesystems to read/write data, improve parallel load balancing and/or scheduling.
[ 2 / 4 ] CPU activity is below 90% (60.22%)
CPU cores are idle more than 10% of time. Threads supposed to run on these cores are probably IO/sync waiting. Some hints: use faster filesystems to read/write data, improve parallel load balancing and/or scheduling.
[ 0 / 4 ] Loop profile is flat
No hotspot found in the application (greatest loop coverage is 3.83%), and the twenty hottest loops cumulated coverage is lower than 20% of the application profiled time (8.55%)
[ 0 / 4 ] Too little time of the experiment time spent in analyzed innermost loops (8.38%)
If the time spent in analyzed innermost loops is less than 15%, standard innermost loop optimizations such as vectorisation will have a limited impact on application performances.
[ 1 / 4 ] Affinity stability is lower than 90% (49.25%)
Threads are often migrating to other CPU cores/threads. For OpenMP, typically set (OMP_PLACES=cores OMP_PROC_BIND=close) or (OMP_PLACES=threads OMP_PROC_BIND=spread). With OpenMPI + OpenMP, use --bind-to core --map-by node:PE=$OMP_NUM_THREADS --report-bindings. With IntelMPI + OpenMP, set I_MPI_PIN_DOMAIN=omp:compact or I_MPI_PIN_DOMAIN=omp:scatter and use -print-rank-map.
[ 3 / 3 ] Less than 10% (0.00%) is spend in BLAS1 operations
It could be more efficient to inline by hand BLAS1 operations
[ 3 / 3 ] Functions mostly use all threads
Functions running on a reduced number of threads (typically sequential code) cover less than 10% of application walltime (0.41%)
[ 3 / 3 ] Cumulative Outermost/In between loops coverage (0.17%) lower than cumulative innermost loop coverage (8.38%)
Having cumulative Outermost/In between loops coverage greater than cumulative innermost loop coverage will make loop optimization more complex
[ 2 / 2 ] Less than 10% (0.00%) is spend in BLAS2 operations
BLAS2 calls usually could make a poor cache usage and could benefit from inlining.
[ 2 / 2 ] Less than 10% (0.00%) is spend in Libm/SVML (special functions)
| Loop ID | Analysis | Penalty Score |
|---|---|---|
| ►Loop 490 - libdmumps.so | Execution Time: 3 % - Vectorization Ratio: 0.00 % - Vector Length Use: 7.29 % | |
| ►Control Flow Issues | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Loop 1939 - libdmumps.so | Execution Time: 2 % - Vectorization Ratio: 0.00 % - Vector Length Use: 1.56 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Loop 1937 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 8.33 % | |
| ○Control Flow Issues | 0 | |
| ►Vectorization Roadblocks | 1000 | |
| ○ | [SA] Too many paths (at least 1000 paths) - Simplify control structure. There are at least 1000 issues ( = paths) costing 1 point. | 1000 |
| ►Loop 854 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 10.27 % | |
| ►Loop Computation Issues | 2 | |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ►Control Flow Issues | 2 | |
| ○ | [SA] Presence of calls - Inline either by compiler or by hand and use SVML for libm calls. There are 2 issues (= calls) costing 1 point each. | 2 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 2 | |
| ○ | [SA] Presence of calls - Inline either by compiler or by hand and use SVML for libm calls. There are 2 issues (= calls) costing 1 point each. | 2 |
| ►Loop 561 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 9.38 % | |
| ►Control Flow Issues | 10 | |
| ○ | [SA] Too many paths (6 paths) - Simplify control structure. There are 6 issues ( = paths) costing 1 point each with a malus of 4 points. | 10 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 10 | |
| ○ | [SA] Too many paths (6 paths) - Simplify control structure. There are 6 issues ( = paths) costing 1 point each with a malus of 4 points. | 10 |
| ►Loop 840 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 10.49 % | |
| ►Control Flow Issues | 1 | |
| ○ | [SA] Presence of calls - Inline either by compiler or by hand and use SVML for libm calls. There are 1 issues (= calls) costing 1 point each. | 1 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 1 | |
| ○ | [SA] Presence of calls - Inline either by compiler or by hand and use SVML for libm calls. There are 1 issues (= calls) costing 1 point each. | 1 |
| ►Loop 1854 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 8.51 % | |
| ►Control Flow Issues | 349 | |
| ○ | [SA] Too many paths (343 paths) - Simplify control structure. There are 343 issues ( = paths) costing 1 point each with a malus of 4 points. | 347 |
| ○ | [SA] Non innermost loop (Outermost) - Collapse loop with innermost ones. This issue costs 2 points. | 2 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 349 | |
| ○ | [SA] Too many paths (343 paths) - Simplify control structure. There are 343 issues ( = paths) costing 1 point each with a malus of 4 points. | 347 |
| ○ | [SA] Non innermost loop (Outermost) - Collapse loop with innermost ones. This issue costs 2 points. | 2 |
| ►Loop 613 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 10.94 % | |
| ►Loop Computation Issues | 11 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ○Loop 92 - libmumps_common.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 6.25 % | |
| ►Loop 2105 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 6.25 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
[ 4 / 4 ] Application profile is long enough (279.42 s)
To have good quality measurements, it is advised that the application profiling time is greater than 10 seconds.
[ 3 / 3 ] Most of time spent in analyzed modules comes from functions with source/debug info
-g option gives access to debugging informations, such are source locations.
[ 0 / 3 ] Architecture specific options are unknown for some functions (compilation options info are not available)
Architecture specific options are needed to produce efficient code for a specific processor ( -march=(target) ).
Architecture specific options are needed to produce efficient code for a specific processor ( -x(target), -ax(target) or -march=(target)).
[ 0 / 3 ] Most of time spent in analyzed modules comes from functions without compilation options informations
Functions without compilation options information cumulate 8.74% of the time spent in analyzed modules. For libdmumps.so, check that both -g and -grecord-gcc-switches are present. For libmumps_common.so, check that both -g and -grecord-gcc-switches are present. Remark: if such options are indeed used, this can also be due to some compiler built-in functions (typically math) or statically linked libraries. This warning can be ignored in that case.
[ 0 / 3 ] Optimization level is unknown for some functions (compilation options info are not available)
To have better performances, it is advised to help the compiler by using a proper optimization level (-O2 of higher). Warning, depending on compilers, faster optimization levels can decrease numeric accuracy.
[ 3 / 3 ] Host configuration allows retrieval of all necessary metrics.
[ 2 / 2 ] Application is correctly profiled ("Others" category represents 0.00 % of the execution time)
To have a representative profiling, it is advised that the category "Others" represents less than 20% of the execution time in order to analyze as much as possible of the user code
[ 1 / 1 ] Lstopo present. The Topology lstopo report will be generated.
[ 0 / 4 ] Too little time of the experiment time spent in analyzed loops (8.33%)
If the time spent in analyzed loops is less than 30%, standard loop optimizations will have a limited impact on application performances.
[ 4 / 4 ] Threads activity is good
On average, more than 108.35% of observed threads are actually active
[ 2 / 4 ] CPU activity is below 90% (57.70%)
CPU cores are idle more than 10% of time. Threads supposed to run on these cores are probably IO/sync waiting. Some hints: use faster filesystems to read/write data, improve parallel load balancing and/or scheduling.
[ 0 / 4 ] Loop profile is flat
No hotspot found in the application (greatest loop coverage is 3.54%), and the twenty hottest loops cumulated coverage is lower than 20% of the application profiled time (8.27%)
[ 0 / 4 ] Too little time of the experiment time spent in analyzed innermost loops (8.23%)
If the time spent in analyzed innermost loops is less than 15%, standard innermost loop optimizations such as vectorisation will have a limited impact on application performances.
[ 2 / 4 ] Affinity stability is lower than 90% (65.34%)
Threads are often migrating to other CPU cores/threads. For OpenMP, typically set (OMP_PLACES=cores OMP_PROC_BIND=close) or (OMP_PLACES=threads OMP_PROC_BIND=spread). With OpenMPI + OpenMP, use --bind-to core --map-by node:PE=$OMP_NUM_THREADS --report-bindings. With IntelMPI + OpenMP, set I_MPI_PIN_DOMAIN=omp:compact or I_MPI_PIN_DOMAIN=omp:scatter and use -print-rank-map.
[ 3 / 3 ] Less than 10% (0.00%) is spend in BLAS1 operations
It could be more efficient to inline by hand BLAS1 operations
[ 3 / 3 ] Functions mostly use all threads
Functions running on a reduced number of threads (typically sequential code) cover less than 10% of application walltime (0.63%)
[ 3 / 3 ] Cumulative Outermost/In between loops coverage (0.09%) lower than cumulative innermost loop coverage (8.23%)
Having cumulative Outermost/In between loops coverage greater than cumulative innermost loop coverage will make loop optimization more complex
[ 2 / 2 ] Less than 10% (0.00%) is spend in BLAS2 operations
BLAS2 calls usually could make a poor cache usage and could benefit from inlining.
[ 2 / 2 ] Less than 10% (0.00%) is spend in Libm/SVML (special functions)
| Loop ID | Analysis | Penalty Score |
|---|---|---|
| ►Loop 490 - libdmumps.so | Execution Time: 3 % - Vectorization Ratio: 0.00 % - Vector Length Use: 7.29 % | |
| ►Control Flow Issues | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Loop 1939 - libdmumps.so | Execution Time: 2 % - Vectorization Ratio: 0.00 % - Vector Length Use: 1.56 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Loop 1937 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 8.33 % | |
| ○Control Flow Issues | 0 | |
| ►Vectorization Roadblocks | 1000 | |
| ○ | [SA] Too many paths (at least 1000 paths) - Simplify control structure. There are at least 1000 issues ( = paths) costing 1 point. | 1000 |
| ►Loop 854 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 10.27 % | |
| ►Loop Computation Issues | 2 | |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ►Control Flow Issues | 2 | |
| ○ | [SA] Presence of calls - Inline either by compiler or by hand and use SVML for libm calls. There are 2 issues (= calls) costing 1 point each. | 2 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 2 | |
| ○ | [SA] Presence of calls - Inline either by compiler or by hand and use SVML for libm calls. There are 2 issues (= calls) costing 1 point each. | 2 |
| ►Loop 561 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 9.38 % | |
| ►Control Flow Issues | 10 | |
| ○ | [SA] Too many paths (6 paths) - Simplify control structure. There are 6 issues ( = paths) costing 1 point each with a malus of 4 points. | 10 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 10 | |
| ○ | [SA] Too many paths (6 paths) - Simplify control structure. There are 6 issues ( = paths) costing 1 point each with a malus of 4 points. | 10 |
| ►Loop 840 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 10.49 % | |
| ►Control Flow Issues | 1 | |
| ○ | [SA] Presence of calls - Inline either by compiler or by hand and use SVML for libm calls. There are 1 issues (= calls) costing 1 point each. | 1 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 1 | |
| ○ | [SA] Presence of calls - Inline either by compiler or by hand and use SVML for libm calls. There are 1 issues (= calls) costing 1 point each. | 1 |
| ►Loop 1802 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Data Access Issues | 8 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ►Loop 613 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 10.94 % | |
| ►Loop Computation Issues | 11 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Loop 1720 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 10.94 % | |
| ►Control Flow Issues | 2 | |
| ○ | [SA] Non innermost loop (Outermost) - Collapse loop with innermost ones. This issue costs 2 points. | 2 |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Vectorization Roadblocks | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ○ | [SA] Non innermost loop (Outermost) - Collapse loop with innermost ones. This issue costs 2 points. | 2 |
| ►Loop 885 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Loop Computation Issues | 6 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ►Data Access Issues | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Vectorization Roadblocks | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
[ 4 / 4 ] Application profile is long enough (179.76 s)
To have good quality measurements, it is advised that the application profiling time is greater than 10 seconds.
[ 3 / 3 ] Most of time spent in analyzed modules comes from functions with source/debug info
-g option gives access to debugging informations, such are source locations.
[ 0 / 3 ] Architecture specific options are unknown for some functions (compilation options info are not available)
Architecture specific options are needed to produce efficient code for a specific processor ( -march=(target) ).
Architecture specific options are needed to produce efficient code for a specific processor ( -x(target), -ax(target) or -march=(target)).
[ 0 / 3 ] Most of time spent in analyzed modules comes from functions without compilation options informations
Functions without compilation options information cumulate 7.29% of the time spent in analyzed modules. For libdmumps.so, check that both -g and -grecord-gcc-switches are present. For libmumps_common.so, check that both -g and -grecord-gcc-switches are present. Remark: if such options are indeed used, this can also be due to some compiler built-in functions (typically math) or statically linked libraries. This warning can be ignored in that case.
[ 0 / 3 ] Optimization level is unknown for some functions (compilation options info are not available)
To have better performances, it is advised to help the compiler by using a proper optimization level (-O2 of higher). Warning, depending on compilers, faster optimization levels can decrease numeric accuracy.
[ 3 / 3 ] Host configuration allows retrieval of all necessary metrics.
[ 2 / 2 ] Application is correctly profiled ("Others" category represents 0.00 % of the execution time)
To have a representative profiling, it is advised that the category "Others" represents less than 20% of the execution time in order to analyze as much as possible of the user code
[ 1 / 1 ] Lstopo present. The Topology lstopo report will be generated.
[ 0 / 4 ] Too little time of the experiment time spent in analyzed loops (5.35%)
If the time spent in analyzed loops is less than 30%, standard loop optimizations will have a limited impact on application performances.
[ 4 / 4 ] Threads activity is good
On average, more than 157.44% of observed threads are actually active
[ 3 / 4 ] CPU activity is below 90% (78.75%)
CPU cores are idle more than 10% of time. Threads supposed to run on these cores are probably IO/sync waiting. Some hints: use faster filesystems to read/write data, improve parallel load balancing and/or scheduling.
[ 0 / 4 ] Loop profile is flat
No hotspot found in the application (greatest loop coverage is 1.58%), and the twenty hottest loops cumulated coverage is lower than 20% of the application profiled time (5.30%)
[ 0 / 4 ] Too little time of the experiment time spent in analyzed innermost loops (5.31%)
If the time spent in analyzed innermost loops is less than 15%, standard innermost loop optimizations such as vectorisation will have a limited impact on application performances.
[ 2 / 4 ] Affinity stability is lower than 90% (62.93%)
Threads are often migrating to other CPU cores/threads. For OpenMP, typically set (OMP_PLACES=cores OMP_PROC_BIND=close) or (OMP_PLACES=threads OMP_PROC_BIND=spread). With OpenMPI + OpenMP, use --bind-to core --map-by node:PE=$OMP_NUM_THREADS --report-bindings. With IntelMPI + OpenMP, set I_MPI_PIN_DOMAIN=omp:compact or I_MPI_PIN_DOMAIN=omp:scatter and use -print-rank-map.
[ 3 / 3 ] Less than 10% (0.00%) is spend in BLAS1 operations
It could be more efficient to inline by hand BLAS1 operations
[ 3 / 3 ] Functions mostly use all threads
Functions running on a reduced number of threads (typically sequential code) cover less than 10% of application walltime (0.00%)
[ 3 / 3 ] Cumulative Outermost/In between loops coverage (0.05%) lower than cumulative innermost loop coverage (5.31%)
Having cumulative Outermost/In between loops coverage greater than cumulative innermost loop coverage will make loop optimization more complex
[ 2 / 2 ] Less than 10% (0.00%) is spend in BLAS2 operations
BLAS2 calls usually could make a poor cache usage and could benefit from inlining.
[ 2 / 2 ] Less than 10% (0.00%) is spend in Libm/SVML (special functions)
| Loop ID | Analysis | Penalty Score |
|---|---|---|
| ►Loop 490 - libdmumps.so | Execution Time: 1 % - Vectorization Ratio: 0.00 % - Vector Length Use: 7.29 % | |
| ►Control Flow Issues | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Loop 1939 - libdmumps.so | Execution Time: 1 % - Vectorization Ratio: 0.00 % - Vector Length Use: 1.56 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Loop 885 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Loop Computation Issues | 6 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ►Data Access Issues | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Vectorization Roadblocks | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Loop 1802 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Data Access Issues | 8 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ►Loop 854 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 10.27 % | |
| ►Loop Computation Issues | 2 | |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ►Control Flow Issues | 2 | |
| ○ | [SA] Presence of calls - Inline either by compiler or by hand and use SVML for libm calls. There are 2 issues (= calls) costing 1 point each. | 2 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 2 | |
| ○ | [SA] Presence of calls - Inline either by compiler or by hand and use SVML for libm calls. There are 2 issues (= calls) costing 1 point each. | 2 |
| ►Loop 179 - libmumps_common.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 6.25 % | |
| ►Loop Computation Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Vectorization Roadblocks | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Loop 1937 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 8.33 % | |
| ○Control Flow Issues | 0 | |
| ►Vectorization Roadblocks | 1000 | |
| ○ | [SA] Too many paths (at least 1000 paths) - Simplify control structure. There are at least 1000 issues ( = paths) costing 1 point. | 1000 |
| ►Loop 561 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 9.38 % | |
| ►Control Flow Issues | 10 | |
| ○ | [SA] Too many paths (6 paths) - Simplify control structure. There are 6 issues ( = paths) costing 1 point each with a malus of 4 points. | 10 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 10 | |
| ○ | [SA] Too many paths (6 paths) - Simplify control structure. There are 6 issues ( = paths) costing 1 point each with a malus of 4 points. | 10 |
| ►Loop 328 - libmumps_common.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 8.68 % | |
| ►Loop Computation Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 8 | |
| ○ | [SA] Several paths (3 paths) - Simplify control structure or force the compiler to use masked instructions. There are 3 issues ( = paths) costing 1 point each. | 3 |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Vectorization Roadblocks | 5 | |
| ○ | [SA] Several paths (3 paths) - Simplify control structure or force the compiler to use masked instructions. There are 3 issues ( = paths) costing 1 point each. | 3 |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Loop 732 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 11.88 % | |
| ►Loop Computation Issues | 11 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 7 | |
| ○ | [SA] Several paths (2 paths) - Simplify control structure or force the compiler to use masked instructions. There are 2 issues ( = paths) costing 1 point each. | 2 |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Several paths (2 paths) - Simplify control structure or force the compiler to use masked instructions. There are 2 issues ( = paths) costing 1 point each. | 2 |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
[ 4 / 4 ] Application profile is long enough (121.88 s)
To have good quality measurements, it is advised that the application profiling time is greater than 10 seconds.
[ 3 / 3 ] Most of time spent in analyzed modules comes from functions with source/debug info
-g option gives access to debugging informations, such are source locations.
[ 0 / 3 ] Architecture specific options are unknown for some functions (compilation options info are not available)
Architecture specific options are needed to produce efficient code for a specific processor ( -march=(target) ).
Architecture specific options are needed to produce efficient code for a specific processor ( -x(target), -ax(target) or -march=(target)).
[ 0 / 3 ] Most of time spent in analyzed modules comes from functions without compilation options informations
Functions without compilation options information cumulate 8.74% of the time spent in analyzed modules. For libdmumps.so, check that both -g and -grecord-gcc-switches are present. For libmumps_common.so, check that both -g and -grecord-gcc-switches are present. Remark: if such options are indeed used, this can also be due to some compiler built-in functions (typically math) or statically linked libraries. This warning can be ignored in that case.
[ 0 / 3 ] Optimization level is unknown for some functions (compilation options info are not available)
To have better performances, it is advised to help the compiler by using a proper optimization level (-O2 of higher). Warning, depending on compilers, faster optimization levels can decrease numeric accuracy.
[ 3 / 3 ] Host configuration allows retrieval of all necessary metrics.
[ 2 / 2 ] Application is correctly profiled ("Others" category represents 0.00 % of the execution time)
To have a representative profiling, it is advised that the category "Others" represents less than 20% of the execution time in order to analyze as much as possible of the user code
[ 1 / 1 ] Lstopo present. The Topology lstopo report will be generated.
[ 0 / 4 ] Too little time of the experiment time spent in analyzed loops (5.66%)
If the time spent in analyzed loops is less than 30%, standard loop optimizations will have a limited impact on application performances.
[ 4 / 4 ] Threads activity is good
On average, more than 267.64% of observed threads are actually active
[ 2 / 4 ] CPU activity is below 90% (66.95%)
CPU cores are idle more than 10% of time. Threads supposed to run on these cores are probably IO/sync waiting. Some hints: use faster filesystems to read/write data, improve parallel load balancing and/or scheduling.
[ 0 / 4 ] Loop profile is flat
No hotspot found in the application (greatest loop coverage is 1.09%), and the twenty hottest loops cumulated coverage is lower than 20% of the application profiled time (5.59%)
[ 0 / 4 ] Too little time of the experiment time spent in analyzed innermost loops (5.62%)
If the time spent in analyzed innermost loops is less than 15%, standard innermost loop optimizations such as vectorisation will have a limited impact on application performances.
[ 2 / 4 ] Affinity stability is lower than 90% (56.00%)
Threads are often migrating to other CPU cores/threads. For OpenMP, typically set (OMP_PLACES=cores OMP_PROC_BIND=close) or (OMP_PLACES=threads OMP_PROC_BIND=spread). With OpenMPI + OpenMP, use --bind-to core --map-by node:PE=$OMP_NUM_THREADS --report-bindings. With IntelMPI + OpenMP, set I_MPI_PIN_DOMAIN=omp:compact or I_MPI_PIN_DOMAIN=omp:scatter and use -print-rank-map.
[ 3 / 3 ] Less than 10% (0.00%) is spend in BLAS1 operations
It could be more efficient to inline by hand BLAS1 operations
[ 3 / 3 ] Functions mostly use all threads
Functions running on a reduced number of threads (typically sequential code) cover less than 10% of application walltime (0.00%)
[ 3 / 3 ] Cumulative Outermost/In between loops coverage (0.04%) lower than cumulative innermost loop coverage (5.62%)
Having cumulative Outermost/In between loops coverage greater than cumulative innermost loop coverage will make loop optimization more complex
[ 2 / 2 ] Less than 10% (0.00%) is spend in BLAS2 operations
BLAS2 calls usually could make a poor cache usage and could benefit from inlining.
[ 2 / 2 ] Less than 10% (0.00%) is spend in Libm/SVML (special functions)
| Loop ID | Analysis | Penalty Score |
|---|---|---|
| ►Loop 490 - libdmumps.so | Execution Time: 1 % - Vectorization Ratio: 0.00 % - Vector Length Use: 7.29 % | |
| ►Control Flow Issues | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Loop 1802 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Data Access Issues | 8 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ►Loop 885 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Loop Computation Issues | 6 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ►Data Access Issues | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Vectorization Roadblocks | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Loop 1939 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 1.56 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Loop 179 - libmumps_common.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 6.25 % | |
| ►Loop Computation Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Vectorization Roadblocks | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Loop 854 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 10.27 % | |
| ►Loop Computation Issues | 2 | |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ►Control Flow Issues | 2 | |
| ○ | [SA] Presence of calls - Inline either by compiler or by hand and use SVML for libm calls. There are 2 issues (= calls) costing 1 point each. | 2 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 2 | |
| ○ | [SA] Presence of calls - Inline either by compiler or by hand and use SVML for libm calls. There are 2 issues (= calls) costing 1 point each. | 2 |
| ►Loop 1922 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 6.25 % | |
| ►Data Access Issues | 12 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 3 issues ( = indirect data accesses) costing 4 point each. | 12 |
| ►Vectorization Roadblocks | 12 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 3 issues ( = indirect data accesses) costing 4 point each. | 12 |
| ►Loop 328 - libmumps_common.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 8.68 % | |
| ►Loop Computation Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 8 | |
| ○ | [SA] Several paths (3 paths) - Simplify control structure or force the compiler to use masked instructions. There are 3 issues ( = paths) costing 1 point each. | 3 |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Vectorization Roadblocks | 5 | |
| ○ | [SA] Several paths (3 paths) - Simplify control structure or force the compiler to use masked instructions. There are 3 issues ( = paths) costing 1 point each. | 3 |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Loop 1937 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 8.33 % | |
| ○Control Flow Issues | 0 | |
| ►Vectorization Roadblocks | 1000 | |
| ○ | [SA] Too many paths (at least 1000 paths) - Simplify control structure. There are at least 1000 issues ( = paths) costing 1 point. | 1000 |
| ►Loop 732 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 11.88 % | |
| ►Loop Computation Issues | 11 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 7 | |
| ○ | [SA] Several paths (2 paths) - Simplify control structure or force the compiler to use masked instructions. There are 2 issues ( = paths) costing 1 point each. | 2 |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Several paths (2 paths) - Simplify control structure or force the compiler to use masked instructions. There are 2 issues ( = paths) costing 1 point each. | 2 |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
[ 4 / 4 ] Application profile is long enough (72.66 s)
To have good quality measurements, it is advised that the application profiling time is greater than 10 seconds.
[ 3 / 3 ] Most of time spent in analyzed modules comes from functions with source/debug info
-g option gives access to debugging informations, such are source locations.
[ 0 / 3 ] Architecture specific options are unknown for some functions (compilation options info are not available)
Architecture specific options are needed to produce efficient code for a specific processor ( -march=(target) ).
Architecture specific options are needed to produce efficient code for a specific processor ( -x(target), -ax(target) or -march=(target)).
[ 0 / 3 ] Most of time spent in analyzed modules comes from functions without compilation options informations
Functions without compilation options information cumulate 8.99% of the time spent in analyzed modules. For libdmumps.so, check that both -g and -grecord-gcc-switches are present. For libmumps_common.so, check that both -g and -grecord-gcc-switches are present. Remark: if such options are indeed used, this can also be due to some compiler built-in functions (typically math) or statically linked libraries. This warning can be ignored in that case.
[ 0 / 3 ] Optimization level is unknown for some functions (compilation options info are not available)
To have better performances, it is advised to help the compiler by using a proper optimization level (-O2 of higher). Warning, depending on compilers, faster optimization levels can decrease numeric accuracy.
[ 3 / 3 ] Host configuration allows retrieval of all necessary metrics.
[ 2 / 2 ] Application is correctly profiled ("Others" category represents 0.01 % of the execution time)
To have a representative profiling, it is advised that the category "Others" represents less than 20% of the execution time in order to analyze as much as possible of the user code
[ 1 / 1 ] Lstopo present. The Topology lstopo report will be generated.
[ 0 / 4 ] Too little time of the experiment time spent in analyzed loops (5.12%)
If the time spent in analyzed loops is less than 30%, standard loop optimizations will have a limited impact on application performances.
[ 4 / 4 ] Threads activity is good
On average, more than 484.21% of observed threads are actually active
[ 2 / 4 ] CPU activity is below 90% (60.60%)
CPU cores are idle more than 10% of time. Threads supposed to run on these cores are probably IO/sync waiting. Some hints: use faster filesystems to read/write data, improve parallel load balancing and/or scheduling.
[ 0 / 4 ] Loop profile is flat
No hotspot found in the application (greatest loop coverage is 1.11%), and the twenty hottest loops cumulated coverage is lower than 20% of the application profiled time (5.06%)
[ 0 / 4 ] Too little time of the experiment time spent in analyzed innermost loops (5.09%)
If the time spent in analyzed innermost loops is less than 15%, standard innermost loop optimizations such as vectorisation will have a limited impact on application performances.
[ 2 / 4 ] Affinity stability is lower than 90% (56.16%)
Threads are often migrating to other CPU cores/threads. For OpenMP, typically set (OMP_PLACES=cores OMP_PROC_BIND=close) or (OMP_PLACES=threads OMP_PROC_BIND=spread). With OpenMPI + OpenMP, use --bind-to core --map-by node:PE=$OMP_NUM_THREADS --report-bindings. With IntelMPI + OpenMP, set I_MPI_PIN_DOMAIN=omp:compact or I_MPI_PIN_DOMAIN=omp:scatter and use -print-rank-map.
[ 3 / 3 ] Less than 10% (0.00%) is spend in BLAS1 operations
It could be more efficient to inline by hand BLAS1 operations
[ 3 / 3 ] Functions mostly use all threads
Functions running on a reduced number of threads (typically sequential code) cover less than 10% of application walltime (0.00%)
[ 3 / 3 ] Cumulative Outermost/In between loops coverage (0.03%) lower than cumulative innermost loop coverage (5.09%)
Having cumulative Outermost/In between loops coverage greater than cumulative innermost loop coverage will make loop optimization more complex
[ 2 / 2 ] Less than 10% (0.00%) is spend in BLAS2 operations
BLAS2 calls usually could make a poor cache usage and could benefit from inlining.
[ 2 / 2 ] Less than 10% (0.00%) is spend in Libm/SVML (special functions)
| Loop ID | Analysis | Penalty Score |
|---|---|---|
| ►Loop 1802 - libdmumps.so | Execution Time: 1 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Data Access Issues | 8 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ►Loop 885 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Loop Computation Issues | 6 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ►Data Access Issues | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Vectorization Roadblocks | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Loop 490 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 7.29 % | |
| ►Control Flow Issues | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Loop 179 - libmumps_common.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 6.25 % | |
| ►Loop Computation Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Vectorization Roadblocks | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Loop 1939 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 1.56 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Loop 328 - libmumps_common.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 8.68 % | |
| ►Loop Computation Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 8 | |
| ○ | [SA] Several paths (3 paths) - Simplify control structure or force the compiler to use masked instructions. There are 3 issues ( = paths) costing 1 point each. | 3 |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Vectorization Roadblocks | 5 | |
| ○ | [SA] Several paths (3 paths) - Simplify control structure or force the compiler to use masked instructions. There are 3 issues ( = paths) costing 1 point each. | 3 |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○Loop 1791 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Loop 732 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 11.88 % | |
| ►Loop Computation Issues | 11 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 7 | |
| ○ | [SA] Several paths (2 paths) - Simplify control structure or force the compiler to use masked instructions. There are 2 issues ( = paths) costing 1 point each. | 2 |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Several paths (2 paths) - Simplify control structure or force the compiler to use masked instructions. There are 2 issues ( = paths) costing 1 point each. | 2 |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Loop 854 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 10.27 % | |
| ►Loop Computation Issues | 2 | |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ►Control Flow Issues | 2 | |
| ○ | [SA] Presence of calls - Inline either by compiler or by hand and use SVML for libm calls. There are 2 issues (= calls) costing 1 point each. | 2 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 2 | |
| ○ | [SA] Presence of calls - Inline either by compiler or by hand and use SVML for libm calls. There are 2 issues (= calls) costing 1 point each. | 2 |
| ►Loop 561 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 9.38 % | |
| ►Control Flow Issues | 10 | |
| ○ | [SA] Too many paths (6 paths) - Simplify control structure. There are 6 issues ( = paths) costing 1 point each with a malus of 4 points. | 10 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 10 | |
| ○ | [SA] Too many paths (6 paths) - Simplify control structure. There are 6 issues ( = paths) costing 1 point each with a malus of 4 points. | 10 |
[ 4 / 4 ] Application profile is long enough (48.13 s)
To have good quality measurements, it is advised that the application profiling time is greater than 10 seconds.
[ 3 / 3 ] Most of time spent in analyzed modules comes from functions with source/debug info
-g option gives access to debugging informations, such are source locations.
[ 0 / 3 ] Architecture specific options are unknown for some functions (compilation options info are not available)
Architecture specific options are needed to produce efficient code for a specific processor ( -march=(target) ).
Architecture specific options are needed to produce efficient code for a specific processor ( -x(target), -ax(target) or -march=(target)).
[ 0 / 3 ] Most of time spent in analyzed modules comes from functions without compilation options informations
Functions without compilation options information cumulate 9.01% of the time spent in analyzed modules. For libdmumps.so, check that both -g and -grecord-gcc-switches are present. For libmumps_common.so, check that both -g and -grecord-gcc-switches are present. Remark: if such options are indeed used, this can also be due to some compiler built-in functions (typically math) or statically linked libraries. This warning can be ignored in that case.
[ 0 / 3 ] Optimization level is unknown for some functions (compilation options info are not available)
To have better performances, it is advised to help the compiler by using a proper optimization level (-O2 of higher). Warning, depending on compilers, faster optimization levels can decrease numeric accuracy.
[ 3 / 3 ] Host configuration allows retrieval of all necessary metrics.
[ 2 / 2 ] Application is correctly profiled ("Others" category represents 0.00 % of the execution time)
To have a representative profiling, it is advised that the category "Others" represents less than 20% of the execution time in order to analyze as much as possible of the user code
[ 1 / 1 ] Lstopo present. The Topology lstopo report will be generated.
[ 0 / 4 ] Too little time of the experiment time spent in analyzed loops (5.24%)
If the time spent in analyzed loops is less than 30%, standard loop optimizations will have a limited impact on application performances.
[ 4 / 4 ] Threads activity is good
On average, more than 796.51% of observed threads are actually active
[ 1 / 4 ] CPU activity is below 90% (49.85%)
CPU cores are idle more than 10% of time. Threads supposed to run on these cores are probably IO/sync waiting. Some hints: use faster filesystems to read/write data, improve parallel load balancing and/or scheduling.
[ 0 / 4 ] Loop profile is flat
No hotspot found in the application (greatest loop coverage is 1.22%), and the twenty hottest loops cumulated coverage is lower than 20% of the application profiled time (5.11%)
[ 0 / 4 ] Too little time of the experiment time spent in analyzed innermost loops (5.19%)
If the time spent in analyzed innermost loops is less than 15%, standard innermost loop optimizations such as vectorisation will have a limited impact on application performances.
[ 2 / 4 ] Affinity stability is lower than 90% (50.30%)
Threads are often migrating to other CPU cores/threads. For OpenMP, typically set (OMP_PLACES=cores OMP_PROC_BIND=close) or (OMP_PLACES=threads OMP_PROC_BIND=spread). With OpenMPI + OpenMP, use --bind-to core --map-by node:PE=$OMP_NUM_THREADS --report-bindings. With IntelMPI + OpenMP, set I_MPI_PIN_DOMAIN=omp:compact or I_MPI_PIN_DOMAIN=omp:scatter and use -print-rank-map.
[ 3 / 3 ] Less than 10% (0.00%) is spend in BLAS1 operations
It could be more efficient to inline by hand BLAS1 operations
[ 3 / 3 ] Functions mostly use all threads
Functions running on a reduced number of threads (typically sequential code) cover less than 10% of application walltime (0.00%)
[ 3 / 3 ] Cumulative Outermost/In between loops coverage (0.05%) lower than cumulative innermost loop coverage (5.19%)
Having cumulative Outermost/In between loops coverage greater than cumulative innermost loop coverage will make loop optimization more complex
[ 2 / 2 ] Less than 10% (0.00%) is spend in BLAS2 operations
BLAS2 calls usually could make a poor cache usage and could benefit from inlining.
[ 2 / 2 ] Less than 10% (0.00%) is spend in Libm/SVML (special functions)
| Loop ID | Analysis | Penalty Score |
|---|---|---|
| ►Loop 1802 - libdmumps.so | Execution Time: 1 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Data Access Issues | 8 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ►Loop 885 - libdmumps.so | Execution Time: 1 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Loop Computation Issues | 6 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ►Data Access Issues | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Vectorization Roadblocks | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Loop 179 - libmumps_common.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 6.25 % | |
| ►Loop Computation Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Vectorization Roadblocks | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Loop 490 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 7.29 % | |
| ►Control Flow Issues | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Loop 1939 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 1.56 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Loop 328 - libmumps_common.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 8.68 % | |
| ►Loop Computation Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 8 | |
| ○ | [SA] Several paths (3 paths) - Simplify control structure or force the compiler to use masked instructions. There are 3 issues ( = paths) costing 1 point each. | 3 |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Vectorization Roadblocks | 5 | |
| ○ | [SA] Several paths (3 paths) - Simplify control structure or force the compiler to use masked instructions. There are 3 issues ( = paths) costing 1 point each. | 3 |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Loop 1922 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 6.25 % | |
| ►Data Access Issues | 12 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 3 issues ( = indirect data accesses) costing 4 point each. | 12 |
| ►Vectorization Roadblocks | 12 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 3 issues ( = indirect data accesses) costing 4 point each. | 12 |
| ○Loop 1791 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Loop 854 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 10.27 % | |
| ►Loop Computation Issues | 2 | |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ►Control Flow Issues | 2 | |
| ○ | [SA] Presence of calls - Inline either by compiler or by hand and use SVML for libm calls. There are 2 issues (= calls) costing 1 point each. | 2 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 2 | |
| ○ | [SA] Presence of calls - Inline either by compiler or by hand and use SVML for libm calls. There are 2 issues (= calls) costing 1 point each. | 2 |
| ►Loop 2827 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 6.25 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
[ 4 / 4 ] Application profile is long enough (40.47 s)
To have good quality measurements, it is advised that the application profiling time is greater than 10 seconds.
[ 3 / 3 ] Most of time spent in analyzed modules comes from functions with source/debug info
-g option gives access to debugging informations, such are source locations.
[ 0 / 3 ] Architecture specific options are unknown for some functions (compilation options info are not available)
Architecture specific options are needed to produce efficient code for a specific processor ( -march=(target) ).
Architecture specific options are needed to produce efficient code for a specific processor ( -x(target), -ax(target) or -march=(target)).
[ 0 / 3 ] Most of time spent in analyzed modules comes from functions without compilation options informations
Functions without compilation options information cumulate 8.85% of the time spent in analyzed modules. For libdmumps.so, check that both -g and -grecord-gcc-switches are present. For libmumps_common.so, check that both -g and -grecord-gcc-switches are present. Remark: if such options are indeed used, this can also be due to some compiler built-in functions (typically math) or statically linked libraries. This warning can be ignored in that case.
[ 0 / 3 ] Optimization level is unknown for some functions (compilation options info are not available)
To have better performances, it is advised to help the compiler by using a proper optimization level (-O2 of higher). Warning, depending on compilers, faster optimization levels can decrease numeric accuracy.
[ 3 / 3 ] Host configuration allows retrieval of all necessary metrics.
[ 2 / 2 ] Application is correctly profiled ("Others" category represents 0.02 % of the execution time)
To have a representative profiling, it is advised that the category "Others" represents less than 20% of the execution time in order to analyze as much as possible of the user code
[ 1 / 1 ] Lstopo present. The Topology lstopo report will be generated.
[ 0 / 4 ] Too little time of the experiment time spent in analyzed loops (4.61%)
If the time spent in analyzed loops is less than 30%, standard loop optimizations will have a limited impact on application performances.
[ 4 / 4 ] Threads activity is good
On average, more than 1531.35% of observed threads are actually active
[ 1 / 4 ] CPU activity is below 90% (47.93%)
CPU cores are idle more than 10% of time. Threads supposed to run on these cores are probably IO/sync waiting. Some hints: use faster filesystems to read/write data, improve parallel load balancing and/or scheduling.
[ 0 / 4 ] Loop profile is flat
No hotspot found in the application (greatest loop coverage is 1.18%), and the twenty hottest loops cumulated coverage is lower than 20% of the application profiled time (4.51%)
[ 0 / 4 ] Too little time of the experiment time spent in analyzed innermost loops (4.58%)
If the time spent in analyzed innermost loops is less than 15%, standard innermost loop optimizations such as vectorisation will have a limited impact on application performances.
[ 1 / 4 ] Affinity stability is lower than 90% (48.96%)
Threads are often migrating to other CPU cores/threads. For OpenMP, typically set (OMP_PLACES=cores OMP_PROC_BIND=close) or (OMP_PLACES=threads OMP_PROC_BIND=spread). With OpenMPI + OpenMP, use --bind-to core --map-by node:PE=$OMP_NUM_THREADS --report-bindings. With IntelMPI + OpenMP, set I_MPI_PIN_DOMAIN=omp:compact or I_MPI_PIN_DOMAIN=omp:scatter and use -print-rank-map.
[ 3 / 3 ] Less than 10% (0.00%) is spend in BLAS1 operations
It could be more efficient to inline by hand BLAS1 operations
[ 3 / 3 ] Functions mostly use all threads
Functions running on a reduced number of threads (typically sequential code) cover less than 10% of application walltime (0.00%)
[ 3 / 3 ] Cumulative Outermost/In between loops coverage (0.04%) lower than cumulative innermost loop coverage (4.58%)
Having cumulative Outermost/In between loops coverage greater than cumulative innermost loop coverage will make loop optimization more complex
[ 2 / 2 ] Less than 10% (0.00%) is spend in BLAS2 operations
BLAS2 calls usually could make a poor cache usage and could benefit from inlining.
[ 2 / 2 ] Less than 10% (0.00%) is spend in Libm/SVML (special functions)
| Loop ID | Analysis | Penalty Score |
|---|---|---|
| ►Loop 1802 - libdmumps.so | Execution Time: 1 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Data Access Issues | 8 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ►Loop 885 - libdmumps.so | Execution Time: 1 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Loop Computation Issues | 6 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ►Data Access Issues | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Vectorization Roadblocks | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Loop 490 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 7.29 % | |
| ►Control Flow Issues | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Loop 179 - libmumps_common.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 6.25 % | |
| ►Loop Computation Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Vectorization Roadblocks | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Loop 1939 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 1.56 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Loop 328 - libmumps_common.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 8.68 % | |
| ►Loop Computation Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 8 | |
| ○ | [SA] Several paths (3 paths) - Simplify control structure or force the compiler to use masked instructions. There are 3 issues ( = paths) costing 1 point each. | 3 |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Vectorization Roadblocks | 5 | |
| ○ | [SA] Several paths (3 paths) - Simplify control structure or force the compiler to use masked instructions. There are 3 issues ( = paths) costing 1 point each. | 3 |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Loop 1922 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 6.25 % | |
| ►Data Access Issues | 12 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 3 issues ( = indirect data accesses) costing 4 point each. | 12 |
| ►Vectorization Roadblocks | 12 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 3 issues ( = indirect data accesses) costing 4 point each. | 12 |
| ○Loop 1791 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Loop 2827 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 6.25 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Loop 854 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 10.27 % | |
| ►Loop Computation Issues | 2 | |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ►Control Flow Issues | 2 | |
| ○ | [SA] Presence of calls - Inline either by compiler or by hand and use SVML for libm calls. There are 2 issues (= calls) costing 1 point each. | 2 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 2 | |
| ○ | [SA] Presence of calls - Inline either by compiler or by hand and use SVML for libm calls. There are 2 issues (= calls) costing 1 point each. | 2 |
[ 4 / 4 ] Application profile is long enough (41.89 s)
To have good quality measurements, it is advised that the application profiling time is greater than 10 seconds.
[ 3 / 3 ] Most of time spent in analyzed modules comes from functions with source/debug info
-g option gives access to debugging informations, such are source locations.
[ 0 / 3 ] Architecture specific options are unknown for some functions (compilation options info are not available)
Architecture specific options are needed to produce efficient code for a specific processor ( -march=(target) ).
Architecture specific options are needed to produce efficient code for a specific processor ( -x(target), -ax(target) or -march=(target)).
[ 0 / 3 ] Most of time spent in analyzed modules comes from functions without compilation options informations
Functions without compilation options information cumulate 8.42% of the time spent in analyzed modules. For libdmumps.so, check that both -g and -grecord-gcc-switches are present. For libmumps_common.so, check that both -g and -grecord-gcc-switches are present. Remark: if such options are indeed used, this can also be due to some compiler built-in functions (typically math) or statically linked libraries. This warning can be ignored in that case.
[ 0 / 3 ] Optimization level is unknown for some functions (compilation options info are not available)
To have better performances, it is advised to help the compiler by using a proper optimization level (-O2 of higher). Warning, depending on compilers, faster optimization levels can decrease numeric accuracy.
[ 3 / 3 ] Host configuration allows retrieval of all necessary metrics.
[ 2 / 2 ] Application is correctly profiled ("Others" category represents 0.05 % of the execution time)
To have a representative profiling, it is advised that the category "Others" represents less than 20% of the execution time in order to analyze as much as possible of the user code
[ 1 / 1 ] Lstopo present. The Topology lstopo report will be generated.
[ 0 / 4 ] Too little time of the experiment time spent in analyzed loops (4.15%)
If the time spent in analyzed loops is less than 30%, standard loop optimizations will have a limited impact on application performances.
[ 4 / 4 ] Threads activity is good
On average, more than 2105.20% of observed threads are actually active
[ 1 / 4 ] CPU activity is below 90% (49.04%)
CPU cores are idle more than 10% of time. Threads supposed to run on these cores are probably IO/sync waiting. Some hints: use faster filesystems to read/write data, improve parallel load balancing and/or scheduling.
[ 0 / 4 ] Loop profile is flat
No hotspot found in the application (greatest loop coverage is 1.16%), and the twenty hottest loops cumulated coverage is lower than 20% of the application profiled time (4.07%)
[ 0 / 4 ] Too little time of the experiment time spent in analyzed innermost loops (4.11%)
If the time spent in analyzed innermost loops is less than 15%, standard innermost loop optimizations such as vectorisation will have a limited impact on application performances.
[ 1 / 4 ] Affinity stability is lower than 90% (48.47%)
Threads are often migrating to other CPU cores/threads. For OpenMP, typically set (OMP_PLACES=cores OMP_PROC_BIND=close) or (OMP_PLACES=threads OMP_PROC_BIND=spread). With OpenMPI + OpenMP, use --bind-to core --map-by node:PE=$OMP_NUM_THREADS --report-bindings. With IntelMPI + OpenMP, set I_MPI_PIN_DOMAIN=omp:compact or I_MPI_PIN_DOMAIN=omp:scatter and use -print-rank-map.
[ 3 / 3 ] Less than 10% (0.00%) is spend in BLAS1 operations
It could be more efficient to inline by hand BLAS1 operations
[ 3 / 3 ] Functions mostly use all threads
Functions running on a reduced number of threads (typically sequential code) cover less than 10% of application walltime (0.00%)
[ 3 / 3 ] Cumulative Outermost/In between loops coverage (0.04%) lower than cumulative innermost loop coverage (4.11%)
Having cumulative Outermost/In between loops coverage greater than cumulative innermost loop coverage will make loop optimization more complex
[ 2 / 2 ] Less than 10% (0.00%) is spend in BLAS2 operations
BLAS2 calls usually could make a poor cache usage and could benefit from inlining.
[ 2 / 2 ] Less than 10% (0.00%) is spend in Libm/SVML (special functions)
| Loop ID | Analysis | Penalty Score |
|---|---|---|
| ►Loop 885 - libdmumps.so | Execution Time: 1 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Loop Computation Issues | 6 | |
| ○ | [SA] Less than 10% of the FP ADD/SUB/MUL arithmetic operations are performed using FMA - Reorganize arithmetic expressions to exhibit potential for FMA. This issue costs 4 points. | 4 |
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 |
| ►Data Access Issues | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Vectorization Roadblocks | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Loop 1802 - libdmumps.so | Execution Time: 1 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Data Access Issues | 8 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 |
| ►Loop 490 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 7.29 % | |
| ►Control Flow Issues | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Data Access Issues | 2 | |
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 |
| ►Vectorization Roadblocks | 20 | |
| ○ | [SA] Too many paths (16 paths) - Simplify control structure. There are 16 issues ( = paths) costing 1 point each with a malus of 4 points. | 20 |
| ►Loop 328 - libmumps_common.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 8.68 % | |
| ►Loop Computation Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 8 | |
| ○ | [SA] Several paths (3 paths) - Simplify control structure or force the compiler to use masked instructions. There are 3 issues ( = paths) costing 1 point each. | 3 |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 2 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Vectorization Roadblocks | 5 | |
| ○ | [SA] Several paths (3 paths) - Simplify control structure or force the compiler to use masked instructions. There are 3 issues ( = paths) costing 1 point each. | 3 |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ►Loop 179 - libmumps_common.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 6.25 % | |
| ►Loop Computation Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Control Flow Issues | 5 | |
| ○ | [SA] Peel/tail loop, considered having a low iteration count - Perform full unroll. Force compiler to use masked instructions. This issue costs 5 points. | 5 |
| ►Data Access Issues | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Vectorization Roadblocks | 6 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Loop 1939 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 1.56 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 2 issues ( = data accesses) costing 2 point each. | 4 |
| ►Loop 1922 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 6.25 % | |
| ►Data Access Issues | 12 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 3 issues ( = indirect data accesses) costing 4 point each. | 12 |
| ►Vectorization Roadblocks | 12 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 3 issues ( = indirect data accesses) costing 4 point each. | 12 |
| ○Loop 1791 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 12.50 % | |
| ►Loop 2827 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 6.25 % | |
| ►Data Access Issues | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Vectorization Roadblocks | 4 | |
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 |
| ►Loop 1937 - libdmumps.so | Execution Time: 0 % - Vectorization Ratio: 0.00 % - Vector Length Use: 8.33 % | |
| ○Control Flow Issues | 0 | |
| ►Vectorization Roadblocks | 1000 | |
| ○ | [SA] Too many paths (at least 1000 paths) - Simplify control structure. There are at least 1000 issues ( = paths) costing 1 point. | 1000 |