Help is available by moving the cursor above any 
symbol or by checking MAQAO website.
[ 4 / 4 ] Application profile is long enough (104.36 s)
To have good quality measurements, it is advised that the application profiling time is greater than 10 seconds.
[ 2.90 / 3 ] Optimization level option is correctly used
[ 2.90 / 3 ] Most of time spent in analyzed modules comes from functions compiled with -g and -fno-omit-frame-pointer
-g option gives access to debugging informations, such are source locations. -fno-omit-frame-pointer improve the accuracy of callchains found during the application profiling.
[ 2.90 / 3 ] Architecture specific option -march=native is used
[ 2 / 2 ] Application is correctly profiled ("Others" category represents 0.03 % of the execution time)
To have a representative profiling, it is advised that the category "Others" represents less than 20% of the execution time in order to analyze as much as possible of the user code
[ 4 / 4 ] Enough time of the experiment time spent in analyzed loops (62.93%)
If the time spent in analyzed loops is less than 30%, standard loop optimizations will have a limited impact on application performances.
[ 4 / 4 ] Loop profile is not flat
At least one loop coverage is greater than 4% (24.28%), representing an hotspot for the application
[ 4 / 4 ] Enough time of the experiment time spent in analyzed innermost loops (62.81%)
If the time spent in analyzed innermost loops is less than 15%, standard innermost loop optimizations such as vectorisation will have a limited impact on application performances.
[ 3 / 3 ] Less than 10% (0%) is spend in BLAS1 operations
It could be more efficient to inline by hand BLAS1 operations
[ 3 / 3 ] Cumulative Outermost/In between loops coverage (0.12%) lower than cumulative innermost loop coverage (62.81%)
Having cumulative Outermost/In between loops coverage greater than cumulative innermost loop coverage will make loop optimization more complex
[ 2 / 2 ] Less than 10% (0%) is spend in Libm/SVML (special functions)
[ 2 / 2 ] Less than 10% (2.42%) is spend in BLAS2 operations
BLAS2 calls usually could make a poor cache usage and could benefit from inlining.
| Loop ID | Module | Analysis | Penalty Score | Coverage (%) | Vectorization Ratio (%) | Vector Length Use (%) |
|---|---|---|---|---|---|---|
| ►887 | exec | Inefficient vectorization. | 2 | 24.28 | 100 | 25 |
| ○ | [SA] Inefficient vectorization: use of shorter than available vector length - Force compiler to use proper vector length. CAUTION: use of 512 bits vectors could be more expensive than 256 bits on some processors. Use intrinsics (costly and not portable). The issue costs 2 points. | 2 | ||||
| ○ | Warning! There is no dynamic data for this loop. Some checks can not been performed. | 0 | ||||
| ►894 | exec | Inefficient vectorization. | 22 | 11.92 | 100 | 50 |
| ○ | [SA] Inefficient vectorization: more than 10% of the vector loads instructions are unaligned - When allocating arrays, don’t forget to align them. There are 10 issues ( = arrays) costing 2 points each | 20 | ||||
| ○ | [SA] Inefficient vectorization: use of shorter than available vector length - Force compiler to use proper vector length. CAUTION: use of 512 bits vectors could be more expensive than 256 bits on some processors. Use intrinsics (costly and not portable). The issue costs 2 points. | 2 | ||||
| ○ | Warning! There is no dynamic data for this loop. Some checks can not been performed. | 0 | ||||
| ►1871 | exec | Partial or unexisting vectorization - Use pragma to force vectorization and check potential dependencies between array access. | 16 | 9.01 | 54.55 | 15.91 |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 6 issues ( = data accesses) costing 2 point each. | 12 | ||||
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 1 issues ( = indirect data accesses) costing 4 point each. | 4 | ||||
| ○2099 | exec | Partial or unexisting vectorization - No issue detected | 0 | 7.28 | 12.77 | 14.1 |
| ►1366 | exec | Partial or unexisting vectorization - Use pragma to force vectorization and check potential dependencies between array access. | 92 | 1.79 | 97.01 | 48.88 |
| ○ | [SA] Presence of expensive FP instructions - Perform hoisting, change algorithm, use SVML or proper numerical library or perform value profiling (count the number of distinct input values). There are 16 issues (= instructions) costing 4 points each. | 64 | ||||
| ○ | [SA] Inefficient vectorization: more than 10% of the vector loads instructions are unaligned - When allocating arrays, don’t forget to align them. There are 9 issues ( = arrays) costing 2 points each | 18 | ||||
| ○ | [SA] Presence of special instructions executing on a single port (BROADCAST) - Simplify data access and try to get stride 1 access. There are 6 issues (= instructions) costing 1 point each. | 6 | ||||
| ○ | [SA] Inefficient vectorization: use of shorter than available vector length - Force compiler to use proper vector length. CAUTION: use of 512 bits vectors could be more expensive than 256 bits on some processors. Use intrinsics (costly and not portable). The issue costs 2 points. | 2 | ||||
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 | ||||
| ○ | Warning! There is no dynamic data for this loop. Some checks can not been performed. | 0 | ||||
| ►400 | exec | Partial or unexisting vectorization - Use pragma to force vectorization and check potential dependencies between array access. | 29 | 1.28 | 89.47 | 44.08 |
| ○ | [SA] Inefficient vectorization: more than 10% of the vector loads instructions are unaligned - When allocating arrays, don’t forget to align them. There are 5 issues ( = arrays) costing 2 points each | 10 | ||||
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 3 issues ( = data accesses) costing 2 point each. | 6 | ||||
| ○ | [SA] Presence of special instructions executing on a single port (COMPRESS/EXPAND, BROADCAST) - Simplify data access and try to get stride 1 access. There are 5 issues (= instructions) costing 1 point each. | 5 | ||||
| ○ | [SA] More than 20% of the loads are accessing the stack - Perform loop splitting to decrease pressure on registers. This issue costs 2 points. | 2 | ||||
| ○ | [SA] Inefficient vectorization: use of shorter than available vector length - Force compiler to use proper vector length. CAUTION: use of 512 bits vectors could be more expensive than 256 bits on some processors. Use intrinsics (costly and not portable). The issue costs 2 points. | 2 | ||||
| ○ | [SA] Inefficient vectorization: use of masked instructions - Simplify control structure. The issue costs 2 points. | 2 | ||||
| ○ | [SA] Presence of a large number of scalar integer instructions - Simplify loop structure, perform loop splitting or perform unroll and jam. This issue costs 2 points. | 2 | ||||
| ○ | Warning! There is no dynamic data for this loop. Some checks can not been performed. | 0 | ||||
| ►2349 | exec | Inefficient vectorization. | 2 | 1.11 | 100 | 50 |
| ○ | [SA] Inefficient vectorization: use of shorter than available vector length - Force compiler to use proper vector length. CAUTION: use of 512 bits vectors could be more expensive than 256 bits on some processors. Use intrinsics (costly and not portable). The issue costs 2 points. | 2 | ||||
| ○ | Warning! There is no dynamic data for this loop. Some checks can not been performed. | 0 | ||||
| ►889 | exec | Partial or unexisting vectorization - Use pragma to force vectorization and check potential dependencies between array access. | 18 | 0.89 | 31.58 | 15.46 |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 5 issues ( = data accesses) costing 2 point each. | 10 | ||||
| ○ | [SA] Presence of indirect accesses - Use array restructuring or gather instructions to lower the cost. There are 2 issues ( = indirect data accesses) costing 4 point each. | 8 | ||||
| ►1007 | exec | Partial or unexisting vectorization - Use pragma to force vectorization and check potential dependencies between array access. | 2 | 0.56 | 33.33 | 16.67 |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 | ||||
| ►994 | exec | Partial or unexisting vectorization - Use pragma to force vectorization and check potential dependencies between array access. | 2 | 0.51 | 33.33 | 16.67 |
| ○ | [SA] Presence of constant non unit stride data access - Use array restructuring, perform loop interchange or use gather instructions to lower a bit the cost. There are 1 issues ( = data accesses) costing 2 point each. | 2 |