[ 4 / 4 ] Application profile is long enough (184.53 s)

To have good quality measurements, it is advised that the application profiling time is greater than 10 seconds.

[ 3 / 3 ] Optimization level option is correctly used

[ 2.40 / 3 ] Most of time spent in analyzed modules comes from functions compiled with -g

-g option gives access to debugging informations, such are source locations. Add -fno-omit-frame-pointer to improve the accuracy of callchains found during the application profiling

[ 3 / 3 ] Host configuration allows retrieval of all necessary metrics.

[ 0 / 3 ] Compilation of some functions is not optimized for the target processor

Application run on the SKYLAKE micro-architecture while the code was specialized for cascadelake.

[ 2 / 2 ] Application is correctly profiled ("Others" category represents 0.00 % of the execution time)

To have a representative profiling, it is advised that the category "Others" represents less than 20% of the execution time in order to analyze as much as possible of the user code

[ 1 / 1 ] Lstopo present. The Topology lstopo report will be generated.

[ 0 / 0 ] Fastmath not used

Consider to add ffast-math to compilation flags (or replace -O3 with -Ofast) to unlock potential extra speedup by relaxing floating-point computation consistency. Warning: floating-point accuracy may be reduced and the compliance to IEEE/ISO rules/specifications for math functions will be relaxed, typically 'errno' will no longer be set after calling some math functions.

[ 4 / 4 ] Application profile is long enough (97.74 s)

To have good quality measurements, it is advised that the application profiling time is greater than 10 seconds.

[ 3 / 3 ] Optimization level option is correctly used

[ 2.40 / 3 ] Most of time spent in analyzed modules comes from functions compiled with -g

-g option gives access to debugging informations, such are source locations. Add -fno-omit-frame-pointer to improve the accuracy of callchains found during the application profiling

[ 3 / 3 ] Host configuration allows retrieval of all necessary metrics.

[ 0 / 3 ] Compilation of some functions is not optimized for the target processor

Application run on the SKYLAKE micro-architecture while the code was specialized for cascadelake.

[ 2 / 2 ] Application is correctly profiled ("Others" category represents 0.00 % of the execution time)

To have a representative profiling, it is advised that the category "Others" represents less than 20% of the execution time in order to analyze as much as possible of the user code

[ 1 / 1 ] Lstopo present. The Topology lstopo report will be generated.

[ 0 / 0 ] Fastmath not used

Consider to add ffast-math to compilation flags (or replace -O3 with -Ofast) to unlock potential extra speedup by relaxing floating-point computation consistency. Warning: floating-point accuracy may be reduced and the compliance to IEEE/ISO rules/specifications for math functions will be relaxed, typically 'errno' will no longer be set after calling some math functions.

[ 4 / 4 ] Application profile is long enough (54.93 s)

To have good quality measurements, it is advised that the application profiling time is greater than 10 seconds.

[ 3 / 3 ] Optimization level option is correctly used

[ 2.40 / 3 ] Most of time spent in analyzed modules comes from functions compiled with -g

-g option gives access to debugging informations, such are source locations. Add -fno-omit-frame-pointer to improve the accuracy of callchains found during the application profiling

[ 3 / 3 ] Host configuration allows retrieval of all necessary metrics.

[ 0 / 3 ] Compilation of some functions is not optimized for the target processor

Application run on the SKYLAKE micro-architecture while the code was specialized for cascadelake.

[ 2 / 2 ] Application is correctly profiled ("Others" category represents 0.00 % of the execution time)

To have a representative profiling, it is advised that the category "Others" represents less than 20% of the execution time in order to analyze as much as possible of the user code

[ 1 / 1 ] Lstopo present. The Topology lstopo report will be generated.

[ 0 / 0 ] Fastmath not used

Consider to add ffast-math to compilation flags (or replace -O3 with -Ofast) to unlock potential extra speedup by relaxing floating-point computation consistency. Warning: floating-point accuracy may be reduced and the compliance to IEEE/ISO rules/specifications for math functions will be relaxed, typically 'errno' will no longer be set after calling some math functions.

[ 4 / 4 ] Enough time of the experiment time spent in analyzed loops (99.77%)

If the time spent in analyzed loops is less than 30%, standard loop optimizations will have a limited impact on application performances.

[ 3 / 4 ] CPU activity is below 90% (89.75%)

CPU cores are idle more than 10% of time. Threads supposed to run on these cores are probably IO/sync waiting. Some hints: use faster filesystems to read/write data, improve parallel load balancing and/or scheduling.

[ 4 / 4 ] Threads activity is good

On average, more than 359.00% of observed threads are actually active

[ 4 / 4 ] Affinity is good (99.60%)

Threads are not migrating to CPU cores: probably successfully pinned

[ 4 / 4 ] Loop profile is not flat

At least one loop coverage is greater than 4% (93.27%), representing an hotspot for the application

[ 4 / 4 ] Enough time of the experiment time spent in analyzed innermost loops (96.88%)

If the time spent in analyzed innermost loops is less than 15%, standard innermost loop optimizations such as vectorisation will have a limited impact on application performances.

[ 3 / 3 ] Cumulative Outermost/In between loops coverage (2.89%) lower than cumulative innermost loop coverage (96.88%)

Having cumulative Outermost/In between loops coverage greater than cumulative innermost loop coverage will make loop optimization more complex

[ 3 / 3 ] Less than 10% (0.00%) is spend in BLAS1 operations

It could be more efficient to inline by hand BLAS1 operations

[ 2 / 2 ] Less than 10% (0.00%) is spend in BLAS2 operations

BLAS2 calls usually could make a poor cache usage and could benefit from inlining.

[ 2 / 2 ] Less than 10% (0.00%) is spend in Libm/SVML (special functions)

[ 4 / 4 ] Application profile is long enough (31.51 s)

To have good quality measurements, it is advised that the application profiling time is greater than 10 seconds.

[ 3 / 3 ] Optimization level option is correctly used

[ 2.40 / 3 ] Most of time spent in analyzed modules comes from functions compiled with -g

-g option gives access to debugging informations, such are source locations. Add -fno-omit-frame-pointer to improve the accuracy of callchains found during the application profiling

[ 3 / 3 ] Host configuration allows retrieval of all necessary metrics.

[ 0 / 3 ] Compilation of some functions is not optimized for the target processor

Application run on the SKYLAKE micro-architecture while the code was specialized for cascadelake.

[ 2 / 2 ] Application is correctly profiled ("Others" category represents 0.00 % of the execution time)

To have a representative profiling, it is advised that the category "Others" represents less than 20% of the execution time in order to analyze as much as possible of the user code

[ 1 / 1 ] Lstopo present. The Topology lstopo report will be generated.

[ 0 / 0 ] Fastmath not used

Consider to add ffast-math to compilation flags (or replace -O3 with -Ofast) to unlock potential extra speedup by relaxing floating-point computation consistency. Warning: floating-point accuracy may be reduced and the compliance to IEEE/ISO rules/specifications for math functions will be relaxed, typically 'errno' will no longer be set after calling some math functions.

[ 4 / 4 ] Enough time of the experiment time spent in analyzed loops (99.52%)

If the time spent in analyzed loops is less than 30%, standard loop optimizations will have a limited impact on application performances.

[ 3 / 4 ] CPU activity is below 90% (80.30%)

CPU cores are idle more than 10% of time. Threads supposed to run on these cores are probably IO/sync waiting. Some hints: use faster filesystems to read/write data, improve parallel load balancing and/or scheduling.

[ 4 / 4 ] Threads activity is good

On average, more than 642.33% of observed threads are actually active

[ 4 / 4 ] Affinity is good (99.18%)

Threads are not migrating to CPU cores: probably successfully pinned

[ 4 / 4 ] Loop profile is not flat

At least one loop coverage is greater than 4% (92.97%), representing an hotspot for the application

[ 4 / 4 ] Enough time of the experiment time spent in analyzed innermost loops (96.50%)

If the time spent in analyzed innermost loops is less than 15%, standard innermost loop optimizations such as vectorisation will have a limited impact on application performances.

[ 3 / 3 ] Cumulative Outermost/In between loops coverage (3.03%) lower than cumulative innermost loop coverage (96.50%)

Having cumulative Outermost/In between loops coverage greater than cumulative innermost loop coverage will make loop optimization more complex

[ 3 / 3 ] Less than 10% (0.00%) is spend in BLAS1 operations

It could be more efficient to inline by hand BLAS1 operations

[ 2 / 2 ] Less than 10% (0.00%) is spend in BLAS2 operations

BLAS2 calls usually could make a poor cache usage and could benefit from inlining.

[ 2 / 2 ] Less than 10% (0.00%) is spend in Libm/SVML (special functions)

[ 4 / 4 ] Application profile is long enough (26.64 s)

To have good quality measurements, it is advised that the application profiling time is greater than 10 seconds.

[ 3 / 3 ] Optimization level option is correctly used

[ 2.40 / 3 ] Most of time spent in analyzed modules comes from functions compiled with -g

-g option gives access to debugging informations, such are source locations. Add -fno-omit-frame-pointer to improve the accuracy of callchains found during the application profiling

[ 3 / 3 ] Host configuration allows retrieval of all necessary metrics.

[ 0 / 3 ] Compilation of some functions is not optimized for the target processor

Application run on the SKYLAKE micro-architecture while the code was specialized for cascadelake.

[ 2 / 2 ] Application is correctly profiled ("Others" category represents 0.00 % of the execution time)

To have a representative profiling, it is advised that the category "Others" represents less than 20% of the execution time in order to analyze as much as possible of the user code

[ 1 / 1 ] Lstopo present. The Topology lstopo report will be generated.

[ 0 / 0 ] Fastmath not used

Consider to add ffast-math to compilation flags (or replace -O3 with -Ofast) to unlock potential extra speedup by relaxing floating-point computation consistency. Warning: floating-point accuracy may be reduced and the compliance to IEEE/ISO rules/specifications for math functions will be relaxed, typically 'errno' will no longer be set after calling some math functions.

[ 4 / 4 ] Enough time of the experiment time spent in analyzed loops (99.38%)

If the time spent in analyzed loops is less than 30%, standard loop optimizations will have a limited impact on application performances.

[ 3 / 4 ] CPU activity is below 90% (76.02%)

CPU cores are idle more than 10% of time. Threads supposed to run on these cores are probably IO/sync waiting. Some hints: use faster filesystems to read/write data, improve parallel load balancing and/or scheduling.

[ 4 / 4 ] Threads activity is good

On average, more than 760.14% of observed threads are actually active

[ 4 / 4 ] Affinity is good (99.00%)

Threads are not migrating to CPU cores: probably successfully pinned

[ 4 / 4 ] Loop profile is not flat

At least one loop coverage is greater than 4% (92.82%), representing an hotspot for the application

[ 4 / 4 ] Enough time of the experiment time spent in analyzed innermost loops (96.35%)

If the time spent in analyzed innermost loops is less than 15%, standard innermost loop optimizations such as vectorisation will have a limited impact on application performances.

[ 3 / 3 ] Cumulative Outermost/In between loops coverage (3.03%) lower than cumulative innermost loop coverage (96.35%)

Having cumulative Outermost/In between loops coverage greater than cumulative innermost loop coverage will make loop optimization more complex

[ 3 / 3 ] Less than 10% (0.00%) is spend in BLAS1 operations

It could be more efficient to inline by hand BLAS1 operations

[ 2 / 2 ] Less than 10% (0.00%) is spend in BLAS2 operations

BLAS2 calls usually could make a poor cache usage and could benefit from inlining.

[ 2 / 2 ] Less than 10% (0.00%) is spend in Libm/SVML (special functions)